Grinding and polishing accessories

Grinding and polishing accessories

Accessories for preparation of any material.

No matter your need discover the different solutions:

  • Achieve a more efficient process
  • Support a reliable result
  • Get better use of the grinding and polishing surfaces

A more efficient grinding and polishing process

Using our grinding and polishing accessories you get an efficient process and improve the reliability of your result. Each accessory has been designed to support an efficient preparation process and give you a reliable result and get better use of your grinding and polishing surfaces.

Specimen holders

Specimen holders

Specimen holders

The specimen holders allow you to grind and polish different shapes and sizes. When the specimens are clamped in the specimen holder you can prepare and clean up to 12 specimens at once saving you process time. The holes are optimized to reach the edges of the preparation surface giving you the best utilization of your preparation surface.

Specimen mover plates

Specimen mover plates

With a specimen mover plate, you can easily grind and polish an odd number of specimens without the need for clamping. This gives you great flexibility when working with a few specimens at a time.

UniForce

UniForce for fast and accurate leveling

A leveling device that enables you to clamp your specimens quickly, correctly, and securely in your specimen holder providing fast and accurate leveling.

The Flexible specimen

Improve workplace safety and reduce your process time by 40 %*

The Flexible specimen holder is the only specimen holder on the market that can hold odd-shaped specimens without clamping. It is a simple way to upgrade your manual grinding and polishing solution to semi-automatic – giving you a safer process with significantly higher reproducibility.

  • Improve health & safety with a more ergonomic process
  • Raise reproducibility with a more consistent process
  • Save time with high efficiency preparation surfaces

See it in action

Flexible specimen holder Manual

Flexible specimen holder flyer

A safer solution for your operators

Manual grinding and polishing can be straining on the operator’s wrist, elbow and shoulder. With the Flexible specimen holder, you can grind and polish a wide range of specimens without holding them by hand – a far more ergonomically correct solution that significantly reduces strain on your wrist, elbow and shoulder.

Higher reproducibility and efficiency

In manual grinding and polishing, even experienced technicians find it difficult to achieve consistent results repeatedly. With the Flexible specimen holder, the specimen is held in place by the specimen mover. This means force is applied evenly across the specimen for the entire process, improving the reproducibility of your results. It also enables you to replace SiC Paper with MD surfaces – a more efficient solution that can reduce process time by up to 40 %*.

CONTACT US TO FIND OUT MORE

* Based on a manual process using SiC Paper versus a semi-automatic process with MD surfaces on a weld joint (75 mm x 25 mm). A manual process using SiC Paper takes approx. 18 minutes; a semi-automatic solution using MD surfaces takes approx. 11 minutes.

Preparation discs

MD Disk with cone

MD Disc

Magnetic fixation discs enable you to change the preparation surface fast and easy. It furthermore ensures less resilience when preparing your specimens. Only for use with our MD surfaces.

MD Aluminium disc

Aluminium disc

For use when preparing your specimens with OP and DP surfaces and other self-adhesive grinding and polishing consumables.

Wet grinding disc

Wet Grinding Disc

The wet grinding disc is for fixation of SiC paper.


*All discs are available with cone or pins depending on your machine.

Special applications

AccuStop

AccuStop

Specimen holder for controlled manual grinding of individual metallographic specimens on SiC grinding paper.

AccuStop is available in two sizes: AccuStop 40 with a capacity up to 40 mm dia. and AccuStop 30 which can be used for specimens up to 30 mm dia.

In the standard form, AccuStop can be used for both cylindrical mounts and for quick fixation by a rubber ring of specimens mounted with a flange by means of Flangeform.

AccuStop-T

AccuStop-T

AccuStop-T is designed specifically for target preparation in the microelectronic industry.

The unique tilt feature of AccuStop-T allows several points in a specimen target plane to be reached at the same time, e.g. rows of solder balls and PCB vias.

The AccuStop-T specimen holder has the ability to tilt the sample +/- 2.0 degrees in any direction.

AccuMeter

AccuMeter

The AccuMeter Measuring Station was developed especially for use with AccuStop-T.

  • Provides easy measurement of the tilt angle and has a micrometer measuring range is 0-25 mm in steps of 10 µm.
  • Useful along with AccuStop 30.

Mold insert

TargetSystem - Mold Insert

Mold insert for use with 40 mm mount cups, 50 pcs.
Max. specimen size 35 x 20 mm.

TargetSystem Parallel Holder

TargetSystem - Parallel Holder

Adapter for parallel polishing (re-usable).
Max. specimen size 23 x 23 mm.

TargetSystem sample chair

TargetSystem sample chair

Adapter for cross-sectioning (disposable).
Max specimen size 27 x 20.5 mm. 50 pcs.

TargetGrip

TargetSystem - TargetGrip

TargetGrip is a tiltable specimen holder. It accommodates mounted samples up to 40 mm in diameter. Adapters are provided for larger specimens, cross-sectioning, and parallel polishing, as well as a 40 mm to 25 mm adapter, which also serves as SEM mount.

Grinding & Polishing consumables